<=Lets Get Started Gantry Side Plates=>
Main Mechanical BOM
First check you have at least all the Mechanical bits in the Bill Of Materials (BOM) Below.
You will likely have extras of a few parts, and also some hardware not listed here, that may not be needed unless particular options were ordered or upgrades are needed.
Main Mechanical BOM:
| Qty | Part | Image |
| 1 | Wide Makerslide X Axis |
 |
| 1 | 2040 Drag Chain Support Extrusion |
 |
| 1 | Makerslide Z Axis 200mm |
 |
| 2 | Makerslide Y Axis 1000mm |
 |
| 2 | 2020 Base (X axis length - 43mm) |
 |
| 3 | 2020 Base (Y_Axis) |
 |
| 2 | Gantry Side Plate |
 |
| 1 | Z Motor Plate |
 |
| 1 | Z Acme Lower Plate |
 |
| 1 | Z Acme Plastic Shim |
 |
| 1 | Spindle Mount Plate |
 |
| 4 | Y End Plates |
 |
| 6 | GT2 Belt Clamp |
 |
| 2 | Drag Chain Support Bracket 1 |
 |
| 2 | Drag Chain Support Bracket 2 |
 |
| 1 | Drag Chain Support Bracket 3 |
 |
| 1 | Extruded X Carriage |
 |
| 1 | 65mm or 69mm Spindle Mount Front (Optional) |
 |
| 1 | 65mm or 69mm Spindle Mount Back (Optional) |
 |
| 10 | Spacer |
 |
| 21 | Dual Bearing V Wheel |
 |
| 6 | Dual Bearing Idler Pulley |
 |
| 10 | Eccentric Nut |
 |
| 4 | GT2 Pulley 1/4in Bore |
 |
| 1 | GT2 Pulley 8mm Bore |
 |
| 2 | F608-2RS Flanged Bearing |
 |
| 1 | Z Acme Thread 232mm |
 |
| 1 | GT2 Closed Loop Belt 80 Tooth |
 |
| 1 | Z Acme Lead Nut Block |
 |
| 10 | Grub Screw- M3x0.5 x 5 (Installed In Pulleys) |
 |
| 4 | Socket Head Cap Screw - M5x0.8 x 10 |
 |
| 8 | Socket Head Cap Screw - M5x0.8 x 16 |
|
| 4 | Socket Head Cap Screw - M5x0.8 x 20 |
 |
| 2 | Pan Head Machine Screw - M2x0.4 x 10 |
 |
| 4 | Pan Head Machine Screw - M2x0.4 x 16 |
 |
| 4 | Socket Button Head Cap Screw - M4 x 0.7 x 10 |
 |
| 26 | Socket Button Head Cap Screw - M5 x 0.8 x 8 |
 |
| 4 | Socket Button Head Cap Screw - M6 x 1 x 10 |
 |
| 36 | Socket Button Head Cap Screw - M5 x 0.8 x 10 |
|
| 20 | Socket Button Head Cap Screw - M5 x 0.8 x 12 |
 |
| 4 | Socket Button Head Cap Screw - M5 x 0.8 x 20 |
 |
| 19 | Socket Button Head Cap Screw - M5 x 0.8 x 25 |
 |
| 8 | Socket Button Head Cap Screw - M5 x 0.8 x 35 |
 |
| 2 | Socket Flat Countersunk Head Cap Screws - M5x35(2) |
 |
| 8 | Socket Flat Countersunk Head Cap Screws - M4x10(2) |
 |
| 54 | Tee Nuts Mix of Pre and Post Assembly |
 |
| 4 | M2 Nut |
 |
| 32 | M5 Washer |
 |
| 10 | Prevailing Torque Hex Nut - M4 x 0.7 |
 |
| 38 | Prevailing Torque Hex Nut - M5 x 0.8 |
 |
| 4 | Nema 23 Stepper |
 |
| 4 | Limit Switch (3 required, 1 spare) |
 |
| 6 | 2020 Right Angle Gusset |
 |
<=Lets Get Started Gantry Side Plates=>